Bouncy Eye Cream ⋅ Gattefossé

In a few words

You will love to apply and re-apply this eye cream. Its bouncy moisturizing texture provides an immediate comfort. On top, Emulium® Dermolea MB thanks to its fine-tuned lipidic compostition brings soothing properties.
With Eyeglorius™ inside, dark circles and puffiness are reduced over time. Never again allow anyone to tell you that you look tired!

Key points

Creaminess
Moisturizing
Anti-dark circles

Upon application

Formule

Phase	Name	INCI	Supplier	%
A1	DEMINERALIZED WATER	WATER	-	67.6
A1	STÄRKINA NATURAL	SOLANUM TUBEROSUM (POTATO) STARCH	AGRANA	1.5
A2	GLYCERIN	GLYCERIN	-	3.0
A2	NATROSOL™ PLUS 330 CS	CETYL HYDROXYETHYLCELLULOSE	ASHLAND	0.4
B	EMULIUM® DERMOLEA MB	POLYGLYCERYL-6 DISTEARATE, CANDELILLA/JOJOBA/RICE BRAN POLYGLYCERYL-3 ESTERS	GATTEFOSSE	5.0
	ACTICIRE® MB	JOJOBA ESTERS, HELIANTHUS ANNUUS (SUNFLOWER) SEED WAX, POLYGLYCERIN-3, ACACIA DECURRENS FLOWER WAX	GATTEFOSSE	2.0
	LIPOCIRE™ A SG	C10-18 TRIGLYCERIDES	GATTEFOSSE	5.0
	LEXFEEL™ N5 MB	DIHEPTYL SUCCINATE, CAPRYLOYL GLYCERIN/SEBACIC ACID COPOLYMER	INOLEX	8.0
	TOCOPHERYL ACETATE	TOCOPHERYL ACETATE	-	0.5
	SENSIVA® SC 50	ETHYLHEXYLGLYCERIN	SCHULKE & MAYR	0.1
C	EYEGLORIUS™	OCTYLDODECYL MYRISTATE, HIPPOPHAE RHAMNOIDES EXTRACT	GATTEFOSSE	2.0
	EUXYL™ K 712	WATER, SODIUM BENZOATE, POTASSIUM SORBATE	SCHULKE & MAYR	1.5
	CELLULOBEADS USF	CELLULOSE	DAITO KASEI	2.0
	RED DYE (1.0% SOL.)	WATER, DYE	-	0.1
	PERFUME BOURRACHE ET POUDRE DE RIZ NATFLOR MKT 1114	PARFUM	TECHNICO-FLOR	0.2
D	CITRIC ACID (10% SOL.)	WATER, CITRIC ACID	-	1.1
				100

Operating instruction

In the main vessel, heat the water of phase A1 between 50-60°C in order to better disperse STÄRKINA NATURAL. Disperse with high shear for 10 minutes (TIP: if the water is too hot, Stärkina creates agglomerates that are difficult to disperse. In case it happens one can disperse with rotor stator to break the
agglomerates).
Prepare the premix of phase A2, add to A1 and disperse with high shear for 5 minutes. Then heat phase A1+A2 at 70°C.
Prepare oil phase B and heat at 70°C. Check that everything is well melted.
Proceed with the emulsion of oil phase B into water phase A1+A2 at 70°C under high shear (rotor stator at 2500-3000 rpm) for 10 minutes.
Cool down under moderate mixing until reaching 40°C.
Below 40°C, add ingredients of phase C one by one and stir under medium shear, until everything is completely incorporated.
Finish to cool down, check pH and adjust with phase D.